TRIAD
- Fox Triad Shock Manual
- 2016 Fox Triad Rear Shock Manual Pdf
- Fox Triad Rear Shock Replacement
- 2016 Fox Triad Rear Shock Manual Download
Installing Your Shock | General Maintenance | Before You Ride | Measuring Sag | Setting Sag | Adjusting Rebound | Adjusting Compression | = 4 && typeof(BSPSPopupOnMouseOver) 'function') BSPSPopupOnMouseOver(event);'>Service Intervals | = 4 && typeof(BSPSPopupOnMouseOver) 'function') BSPSPopupOnMouseOver(event);'>Important Safety Information | Stuck Down Shock | Air Sleeve Maintenance
weight Gba emulator for pc. | 0.47 lbs./213 g (6.50' x 1.50' No reducers) |
features/adjustments | lightweight chassis, DOHC ProPedal Technology that provides pedaling efficiency as well as control and sensitivity for big and small hits. with 2 positions, air spring pressure, rebound adjust |
spring | air |
intended use | freeride A style of riding that is defined by short course technical acrobatics and athletes that defy gravity. Generally, the bikes and components required for freeriding are stronger and heavier than their lightweight cross-country brethren. Combine the aerial pyrotechnics of freeriding with some longer trails and courses, as is typical of cross-country riding, and now you're looking at all-mountain riding., all-mountain A style of bicycle riding that melds the stamina and conditioning required of cross-country with the technical abilities of freeriding., cross-country A style of bicycle riding that is defined by long rides, lightweight bicycles and stamina. |
Triad Supplement Specialized Bikes: English » 2004: Rear Shocks: English » French » German » Italian » Spanish » 2003: Rear Shocks: English » French » German » Italian » Spanish » 2003: Vanilla DH Intense + M1: English » 2003: Vanilla DH Kona Stab Primo: English » 2003: Vanilla DH Supplement: English » 2002: Rear Shocks. Fox DPS METRIC Factory 2020Peak Racing PerformanceWith a new and improved EVOL air sleeve, Fox's 2020 DPS Factory Rear Shock offers increased responsiveness and sensitivity. The updated valve design delivers improved compression and rebound flow, and the Factory series comes. Jan 12, 2007 I have recently purchased a 2006 Stumpjumper FSR Comp and want to know if it is possible to replace the stock Triad rear shock with an after market shock, in particular the Rockshox Pearl 3.1 and I do not know much about rear shock sizing. I understand the stock Fox Triad shock is 7.5' x 1.75' and the Rockshox Pearl 3.1 is 7.5' x 2.0'.
Installing Your Shock
Some bicycles feature a FOX Racing Shox TRIAD shock. The TRIAD has three on-the-fly suspension settings: 1. OPEN (DESCENDING) 2. PROPEDAL (FOR BUMP COMPLIANCE AND PEDALING EFFICIENCY) 3. LOCKED (CLIMBING & ROAD RIDING) Use the different settings to tune the shock to different riding conditions and situations. Jan 26, 2016 I have a Triad shock on my 2010 stump jumper and just recently I noticed it leaking oil out of the valve adjustment for the lockout. I went to adjust Fox Triad (Float) Rear Suspension leaked all oil out- Mtbr.com.
If you are installing your shock on a bike in which the shock is not original equipment:
- Install the shock.
- Remove the main air chamber air cap and let all the air out of the main air chamber.
- Carefully cycle the suspension through its entire travel The total amount the shock or fork compresses. On a shock it is measured using the eye-to-eye distance or shaft travel..
- Check that all parts of the shock are clear of the frame and swingarm as it cycles through the travel.
- Pressurize your main air chamber to a minimum of 50 psi and no more than 300 psi. You will tune to a more specific air pressure in the Setting Sag section below.
- Set sag.
![2016 2016](https://www.ridefox.com/fox17/img/help/page593-B6YW/FLOAT-DPS-3pos-w-adj-LV-EVOL-m.jpg)
General Maintenance
There may be a small amount of air sleeve lubricant residue on the body. This is normal. If this residual air sleeve lubricant is not present, this is an indication that the air sleeve should be re-lubricated. Some other things to consider for all shock models:
Fox Triad Shock Manual
- If you ride in extreme conditions, service your shock and air sleeve more frequently. Check the maintenance schedule for your shock.
- Wash your shock with soap and water only.
- Do not use a high pressure washer to clean your shock.
- Internal service should be performed by FOX Racing Shox or an Authorized Service Center.
Before You Ride
- Clean the outside of your shock with soap and water and wipe dry with a soft dry rag. Do not use a high pressure washer on your shock.
- Inspect entire exterior of shock for damage. The shock should not be used if any of the exterior parts appear to be damaged. Please contact your local dealer or FOX Racing Shox for further inspection and repair.
- Check that quick-release levers (or thru-axle pinch bolts) are properly adjusted and tightened.
- Check headset adjustment. Adjust headset if loose, according to manufacturer’s recommendations.
- Check that brake cables or hoses are properly fastened.
- Check that the front and rear brakes operate properly on flat land.
Setting Sag
You can also view a Flash video on Setting Sag.
To get the best performance from your TRIAD shock, it is necessary to set sag Amount a shock or fork compresses with the rider sitting on the bike in a normal riding position. Best measured with an assistant holding your bike up and with the rider in full riding gear. On a fork, it is helpful to place a ZIP tie around one of the upper tubes.. To set sag:
- Locate the Schrader air valve on the shock and remove the valve cap.
- Screw the FOX Racing Shox High Pressure pump onto the air valve until the pump shows pressure on the gauge. Do not over-tighten the valve chuck.
- Add air pressure until desired pressure is shown on the gauge. Refer to the appropriate Triad Air Spring Settings table below.
Check your bicycle owner's manual as manufacturers may specify specific settings that correspond to different rear suspension designs. All things being equal, your bicycle's owner's manual settings take precedence overthe settings shown in the table below.
- Unthread the pump from the air valve and measure sag.5. Repeat steps 2-4 until proper sag is achieved, then replace the air valve cap.
TRIAD AIR SPRING SETTINGS | |
Rider Weight lbs. (kg) | Main Air Chamber Pressure PSI |
90 - 100 (41 - 45) | 95 - 100 |
110 - 110 (45 - 50) | 100 - 110 |
110 - 120 (50 - 54) | 110 - 120 |
120 - 130 (54 - 60) | 120 - 125 |
130 - 140 (60 - 64) | 125 - 130 |
140 - 150 (64 - 68) | 130 - 135 |
150 - 160 (68 - 73) | 135 - 140 |
160 - 170 (73 - 77) | 140 - 150 |
170 - 180 (77 - 82) | 150 - 160 |
180 - 190 (82 - 86) | 160 - 170 |
190 - 200 (86 - 91) | 170 - 180 |
200 - 210 (91 - 95) | 180 - 190 |
210 - 220 (95 - 100) | 190 - 200 |
220 - 230 (100 - 104) | 200 - 210 |
230 - 240 (104 - 109) | 210 - 220 |
240 - 250 (109 - 113) | 220 - 230 |
250 - 265 (113 - 120) | 230 - 240 |
265 - 280 (120 - 127) | 240 - 250 |
280 - 295 (127 - 134) | How to install dmg mac. 250 - 260 |
Adjusting Rebound
Rebound controls the rate at which your shock returns after it has been compressed. The proper rebound setting is a personal preference, and changes with rider weight, riding style and conditions. A rule of thumb is that rebound should be as fast as possible without kicking back and pushing the rider off the saddle.
The rebound knob has 8-10 clicks of adjustment.
For slower rebound, turn the red adjuster knob = 4 && typeof(BSPSPopupOnMouseOver) 'function') BSPSPopupOnMouseOver(event);'>clockwise.
For faster rebound, turn the red adjuster knob counterclockwise.
Adjusting Compression
Some bicycles feature a FOX Racing Shox TRIAD shock. The TRIAD has three on-the-fly suspension settings:
1. OPEN (DESCENDING)
2. PROPEDAL (FOR BUMP COMPLIANCE AND PEDALING EFFICIENCY)
2016 Fox Triad Rear Shock Manual Pdf
3. LOCKED (CLIMBING & ROAD RIDING)
Use the different settings to tune the shock to different riding conditions and situations. For example, use the PROPEDAL or LOCKED position for riding to the top of the mountain, and then switch to the OPEN position for the descent. Because suspension designs and riding skills vary, optimal settings can vary from bike to bike and rider to rider. How to move to end of document in word for mac download.
Fox Triad Rear Shock Replacement
To determine which compression adjust position is best, pedal the bicycle at about 15 MPH and monitor the shock movement. Switch between positions and select the one that reduces suspension movement most effectively while providing the desired amount of bump absorption. The setting may change depending on conditions and riding styles.
2016 Fox Triad Rear Shock Manual Download
eng076